BOM calculator + decision reportFirst recorded · Reviewed

Humanoid Robot Actuators Percentage of BOM

Actuators cost percentage in humanoid robot BOM depends on scope and configuration. McKinsey’s April 2026 analysis gives a 40–60% reference range. Check the source and accounting limits. Calculate your own share below using complete-module quotes; the default 60.9% is an illustrative scenario.

Model and editorial responsibility: Humanoid Robot Actuators. Public references and model assumptions are identified separately.

Calculate your BOM share

Required: $1–$1,000,000 per robot. Hardware only; all results update immediately.

Actuator share of your hardware BOM

60.9%

$23,135.20 actuation · 40 physical units

Remaining hardware budget: $14,864.80

Actuator allocation within the hardware budget

Actuators 60.9% · Other hardware budget 39.1%

Illustrative estimate from editorial assumptions; no OEM costs or industry benchmark.

See formula, assumptions and limits
Example presets:

Presets are hypothetical architectures. Counts represent physical actuator units, not robot or hand degrees of freedom.

Configure architecture and prices
Actuator BOM inputs

0–34 complete modules including motor, reducer, bearings, encoder and driver.

0–20 complete modules including motor, screw, bearings, encoder and driver.

0–24 motors with gearhead, driver and encoder. Excludes tactile arrays and passive hand structure.

Production scenario (assumed discount)
Sourcing price assumption

Scenario factors only; no supplier, region or quality guarantee.

Explain and act on the result
Per-robot calculation in USD. Complete modules are counted once.
AssemblyCount × unit priceSubtotal
Rotary14 × $638.00$8,932.00
Linear14 × $924.00$12,936.00
Hand motors12 × $105.60$1,267.20
Actuator total$23,135.20

Formula: $23,135.20 ÷ $38,000.00 × 100 = 60.9%. Dollar amounts use cents; the percentage is rounded for display.

Next: confirm quote inclusions and duty requirements using the RFQ checklist. This model does not validate torque, thermal limits, life or safety.

Request a scoped quote

Model version 2026-10-27. Exports include inputs, prices, scope and limitations. No server calculation or waiting period is required.

Actuators cost percentage in humanoid robot BOM: decision conclusions

The tool above answers your cost-allocation question. The report below explains what the number can support. All numeric scenarios are editorial assumptions; public sources are used only for the specific facts identified.

A percentage needs a defined denominator

Use a per-robot hardware BOM. Retail price, total ownership cost and capital expenditure answer different questions.

See scope table
The default is 60.9%, not an industry average

14 rotary modules, 14 linear modules and 12 hand motors total $23,135.20 against a $38,000 hardware BOM.

Reproduce the calculation
Configuration is public; the cost split may not be

Unitree lists base and EDU joint configurations, but its product page does not disclose their actuator BOM. Do not infer manufacturing cost from a list price.

Read source and limits
A cheaper scenario still needs qualification

Torque ratings distinguish normal operation from repeated and momentary peaks. A lower-priced actuator is not automatically suitable for the same duty cycle.

Read catalog evidence
Default scenario allocation, not a measured robot BOM60.9%Illustrative actuation

Where the default hardware budget goes

Rotary modules$8,932.00
Linear modules$12,936.00
Hand motor assemblies$1,267.20
Remaining hardware budget$14,864.80

Derived from the default Hybrid preset. Remaining budget is unallocated, not an estimate of actual compute, battery or chassis costs. This static report example does not follow your edited inputs.

Method: make the cost share reproducible

Four steps to a reproducible actuator BOM shareUnit counts× Unit pricesSum costs÷ Total BOMActuator share (%) = total actuator hardware cost / total hardware BOM × 100
Use the same currency, quantity basis and hardware scope in the numerator and denominator. The equation is an accounting identity, not a forecast.

Actuation cost A = rotary count × rotary unit price + linear count × linear unit price + hand motor count × hand assembly unit price.

Actuator share = A ÷ total robot hardware BOM × 100. Remaining hardware budget = total BOM − A.

Model prices = prototype base price × production factor × sourcing factor, rounded to cents before multiplying by physical unit counts. User-entered prices bypass both factors. Percentages display one decimal place.

Model version 2026-10-27. Every price and factor in this table is an illustrative assumption, not sourced pricing.
Model inputAssumptionDefault pilot result / effect
Rotary complete module$1,450.00$638.00 × 14 = $8,932.00
Linear complete module$2,100.00$924.00 × 14 = $12,936.00
Hand motor assembly$240.00$105.60 × 12 = $1,267.20
Production factorsPrototype ×1.00; Pilot ×0.44; Volume ×0.19Default Pilot ×0.44
Sourcing factorsBaseline assumption ×1.00; Higher-cost assumption ×1.45Default baseline ×1.00; no brand or region implication
Default total$23,135.20 ÷ $38,000.00 × 10060.9%; $14,864.80 remains

Model coverage: up to 34 rotary modules, 20 linear modules and 24 hand motors; USD amounts accept two decimal places. These are tool input limits, not kinematic limits on real humanoids. Count physical actuators, since parallel linkages and tendon systems need not map one motor to one DoF.

BOM scope: include each component once

Keep this scope consistent when replacing assumptions with supplier quotations.
Cost groupActuator numeratorTotal hardware denominator / action
Complete body joint modulesMotor, transmission, bearings, encoder, housing and driverInclude in total hardware; do not add bundled drivers or encoders again
Hand motor assembliesMotor, gearhead, driver and encoder across both handsInclude once; quote passive hand structure, tendons and tactile arrays separately
Other hardwareExcluded from actuator numeratorCompute, perception, chassis, battery, power distribution, wiring and passive hand parts
Manufacturing overheadExcluded from this modelTrack assembly labor, testing, scrap, tooling and logistics in a separate manufacturing-cost model
Commercial and operating costsExcludedRetail margin, software, support, taxes, electricity and maintenance do not belong in this hardware BOM ratio

An unbundled quote must be completed before comparing it with a complete module. If your accounting uses a different scope, reconcile it explicitly; otherwise a numerically correct percentage can still be misleading.

Need to choose complete assemblies? Compare humanoid actuator manufacturers using the same inclusion list, then prepare your actuator RFQ.

Public evidence: what is known and what remains unknown

Sources checked October 27, 2026. Publication dates below belong to the original documents; this review does not turn older estimates into current prices. N/A means the linked document does not establish the requested cost split.

Evidence map for the linked primary documents, not an OEM cost league table.
Document / platformSupported factActuator BOM / shareDecision implication
McKinsey, April 2026Analyst hardware cost allocation; hand scope overlaps other categories40–60% reference range, not an OEM disclosureReconcile inclusions before comparing with your own quoted BOM
Unitree G1 / G1 EDU23 base joint DoF; 23–43 EDU configuration rangeN/A — not disclosed in the linked specificationsSpecify the exact hand and wrist configuration before requesting prices
Goldman Sachs, January 2024Historical high-spec robot cost estimate changed substantiallyN/A — this page does not use a verified 2026 OEM actuator shareDo not extrapolate a historical total-cost trend into a universal actuation ratio
Harmonic Drive CSF MiniRated, repeated peak and momentary peak torque are distinctN/A — technical catalog, not a robot BOMMatch duty and life before substituting a cheaper transmission
Electric Atlas announcement, April 2024Transition to a fully electric platformN/A — no itemized cost split in the announcementArchitecture changes alone do not quantify BOM savings

Public evidence is insufficient here to present Tesla, Figure or Unitree actuator dollars as verified manufacturing costs. The calculator therefore uses neutral scenario names and exposes its full assumptions. A different third-party estimate may use a different generation, volume or accounting scope; reconcile those before comparing percentages.

Uncertainty: test unit prices and the denominator separately

Sensitivity to all three unit prices at a fixed $38,000 total BOMPrices −20%48.7%Base prices60.9%Prices +20%73.1%
A chosen ±20% stress test with fixed counts and denominator. These are scenarios, not confidence intervals, probabilities or supplier price bounds. The table below supplies exact dollars.
Illustrative stress tests using the default 14 rotary, 14 linear and 12 hand motors. Each row changes only the named input.
ScenarioActuator cost (USD)Total BOM (USD)ShareInterpretation
All unit prices −20%$18,508.16$38,000.0048.7%Hypothetical quote reduction; verify unchanged specifications
Default prices$23,135.20$38,000.0060.9%Baseline assumption, not a measured midpoint
All unit prices +20%$27,762.24$38,000.0073.1%Stress case, not a statistical upper bound
Only total BOM +20%$23,135.20$45,600.0050.7%Percentage falls with zero actuator dollar savings

The ±20% variation is a chosen illustration, not a measured distribution. Use your own quote range. At a fixed denominator, a $100 change in each of 14 rotary modules changes actuator spend by $1,400 and share by 3.7 percentage points on a $38,000 BOM. Budget confidence comes from scoped quotations, not the number of decimals displayed.

Production scale: a scenario factor is not a forecast

Assumed production factors, not an observed learning curve138.4%Prototype ×1.0060.9%Pilot ×0.4426.3%Volume ×0.19
Static scenario comparison using the same counts, sourcing factor and $38,000 denominator. A cheaper actuator package does not prove that total robot BOM or retail price will decline at the same rate.
Same default architecture, baseline sourcing and $38,000 denominator at every scale. Assumed recurring prices only.
Production scenarioAssumed factorActuation costBOM shareWhat must be confirmed
Prototype×1.00$52,580.00138.4%Actual annual demand, tooling, yield, MOQ and a quote with matching scope
Pilot×0.44$23,135.2060.9%Actual annual demand, tooling, yield, MOQ and a quote with matching scope
Volume×0.19$9,990.2026.3%Actual annual demand, tooling, yield, MOQ and a quote with matching scope

No observed learning rate is claimed. A large nominal discount can be outweighed by non-recurring tooling or low yield. Request those separately, allocate tooling over committed units, and compare fully burdened manufacturing cost alongside hardware BOM.

Architecture trade-offs: compare requirements before price

Engineering review prompts, not normalized performance scores or guarantees. Supplier data and task testing are required.
AlternativePotential reason to consider itBoundary / cost riskMinimum validation
Rotary integrated modulePackage joint components as a complete recurring-cost itemReducer, bearing and driver inclusions vary; peak rating is not continuous ratingDuty-cycle torque, speed, thermal path and bearing-load specification
Linear screw moduleFit a linkage with axial thrust requirementsLinkage geometry, screw life, lubrication and buckling alter sizing and costForce / speed envelope, stroke, impact loads and life calculation
Lower-ratio rotary driveExplore backdrivability and transmission changes for a dynamic taskMotor sizing, heat and holding requirements may offset gearbox savingsWhole-joint efficiency and thermal test at the required task load
Simpler or underactuated handReduce the number of separately driven motor assembliesLower motor count may reduce grasp control or transfer cost into tendons and sensingRepresentative grasp success, service intervals and full end-effector cost

These are selection questions. They do not imply a specific robot uses the listed transmission, that a region guarantees lower cost, or that an architecture can safely replace another without redesign.

Risks, limits and practical alternatives

Use the cost result for allocation; qualify the hardware separately.
RiskHow a decision can go wrongMitigation / alternative
Misuse of the resultA low percentage is treated as proof of safety or feasible torqueCheck duty-specific ratings and test the full joint. See the CSF Mini rating definitions in the source registry
Cost omission / double countingA complete module and its bundled reducer are both added; or hand electronics are omittedUse the scope table and a supplier inclusion checklist; complete unbundled quotes
Scenario mismatchA lab quote is scaled using an assumed volume factor without a committed orderObtain a quote at the real annual volume; track tooling and yield separately
Thermal and life mismatchPeak torque is used to size continuous duty; impact cycles and cooling are ignoredProvide actual load and ambient profiles; request thermal and life evidence for the selected part
Unfunded remainderA percentage below 100% is accepted even though the remainder cannot buy the other hardwarePrice compute, battery, structure, wiring and sensors independently; revise the total BOM
Uncertain or unavailable pricingModel numbers become a purchase commitmentExport the assumptions, gather comparable quotations and rerun a low / high price case

Worked examples: reproduce the result, then choose a next action

These three hypothetical cases use the same calculation function as the live tool. They are not OEM teardowns, payload certifications or manufacturing forecasts. Load the matching preset above to reproduce each one.

Hybrid scenario

Illustrative mixed architecture: 28 body actuators and 12 hand motors.

Hybrid: Pilot, Baseline assumption; USD per robot.
Line itemCountUnit priceLine total
Rotary modules14$638.00$8,932.00
Linear modules14$924.00$12,936.00
Hand motor assemblies12$105.60$1,267.20
Actuator total40Sum of the three lines$23,135.20
Other hardware budgetUnallocatedTotal BOM minus actuator total$14,864.80
Total hardware BOMDenominatorActuator total plus remaining budget$38,000.00

Result: $23,135.20 ÷ $38,000.00 × 100 = 60.9%. Next: obtain scoped quotes for the rotary and linear modules before treating the split as a procurement budget.

All rotary scenario

Illustrative all-rotary alternative; mechanical equivalence is not assumed.

All rotary: Pilot, Baseline assumption; USD per robot.
Line itemCountUnit priceLine total
Rotary modules28$638.00$17,864.00
Linear modules0$924.00$0.00
Hand motor assemblies12$105.60$1,267.20
Actuator total40Sum of the three lines$19,131.20
Other hardware budgetUnallocatedTotal BOM minus actuator total$16,868.80
Total hardware BOMDenominatorActuator total plus remaining budget$36,000.00

Result: $19,131.20 ÷ $36,000.00 × 100 = 53.1%. Next: validate an all-rotary layout against the same task envelope before comparing its cost with a mixed architecture.

Lean volume scenario

Aggressive volume assumption; requires supplier quotes and qualification.

Lean volume: Volume, Baseline assumption; USD per robot.
Line itemCountUnit priceLine total
Rotary modules23$275.50$6,336.50
Linear modules0$399.00$0.00
Hand motor assemblies6$45.60$273.60
Actuator total29Sum of the three lines$6,610.10
Other hardware budgetUnallocatedTotal BOM minus actuator total$2,889.90
Total hardware BOMDenominatorActuator total plus remaining budget$9,500.00

Result: $6,610.10 ÷ $9,500.00 × 100 = 69.6%. Next: challenge the volume discount with a supplier quote, tooling allocation and yield assumptions.

Next step: turn an allocation estimate into comparable quotes

Send the same requirement envelope to each supplier and keep recurring and non-recurring costs separate.
RFQ fieldWhat to provideWhat to ask back
Task and joint listPhysical module count, rotary / linear type, hand assembly scopeA line item for each included assembly and bundled subcomponent
Load and motionContinuous and peak torque / thrust, speed, external loads and duty cycleRatings for your load profile, not just a peak headline
Environment and lifeCooling, ambient temperature, shock cycles, service life and ingress needsTest evidence, maintenance needs and life assumptions
Electrical and controlBus voltage, driver, encoder, torque sensing and communication requirementsExact inclusion / exclusion list, interface compatibility and calibration costs
Commercial basisAnnual quantity, batch size, currency, quote validity and delivery locationRecurring unit price, tooling, MOQ, lead time, tax and shipping separated

BOM calculator FAQ

Cost and scope

What is the actuators cost percentage in humanoid robot BOM?

Divide included actuator hardware cost by total hardware BOM and multiply by 100. McKinsey’s April 17, 2026 analysis gives a 40–60% reference range; reconcile hand and sensing scope before comparing it. No universal verified percentage applies to every humanoid. This calculator’s default 60.9% is a separate illustrative result, not an industry average or supplier quote. See the source registry for the original analysis and its limits.

Does a lower percentage mean a better design?

No. Increasing the compute or structure budget alone lowers the percentage without saving any actuator dollars. Compare the absolute spend, remaining budget and task performance before choosing a design.

Can I use the retail price as the denominator?

Use a hardware BOM denominator. Retail price can include margin, software, support, tax and distribution, so it produces a different ratio and should not be labeled actuator share of BOM.

Are hand motors counted separately from hand DoF?

Yes. Enter the physical motor count across both hands. A tendon or underactuated mechanism can move several joints using one motor; DoF is not a substitute for the motor count.

Using the calculator

How do I replace the model with supplier quotes?

Choose Use my unit prices and enter a complete rotary module price, complete linear module price and hand motor assembly price in USD per unit. These prices bypass all production and sourcing multipliers. For an unused category, keep its positive default price and set its count to zero.

Are production discounts guaranteed?

No. The 1.00, 0.44 and 0.19 factors are hypothetical scenario controls. Tooling, yield, minimum order quantities and specifications can change the actual relationship. A volume selection is not a supplier offer.

What happens if actuators exceed the total BOM?

The calculator shows the true percentage, which can exceed 100%, and a dollar budget shortfall. It does not show a negative allocation for other hardware. Revise the total BOM or obtain lower quotes while retaining the required specifications.

Can I calculate with no actuators or a blank budget?

No decision result is shown. A zero actuator count asks you to add at least one unit; a blank, invalid or out-of-range field asks you to correct it. Reset defaults is always available.

Evidence and decisions

Does this report disclose Tesla, Figure or Unitree manufacturing costs?

No. The cited public documents do not establish their itemized actuator costs. Branded cost presets and unsupported teardown percentages are not used as evidence. Request configuration-specific quotations instead.

Should I replace a roller screw with a rotary module to save cost?

Only after checking torque or thrust, transmission geometry, packaging, efficiency, thermal behavior, impact loads and service life for the task. The calculator compares cost assumptions; it does not prove that two architectures are mechanically interchangeable.

What belongs in an actuator RFQ?

Specify continuous and peak torque or thrust, duty cycle, output speed, external loads, voltage, temperature and cooling limits, backlash, sensing, life target, annual quantity and included components. Ask suppliers to separate tooling, recurring price and qualification costs.

How are uncertainty and confidentiality handled?

Run lower and higher unit-price cases using your own quote ranges. Copying or downloading exports only the model you see. Contacting the engineering team is a separate action. No statistical confidence interval is claimed.

Source registry and evidence boundaries

Accessed October 27, 2026. Undated documents are identified as such. Each source supports only the finding listed; none is used to authenticate the calculator’s default prices or multipliers.

McKinsey & Company

Turning humanoid supply chain constraints into billion-dollar wins (opens in a new tab)

Publication: 2026-04-17 · Accessed October 27, 2026

Locator: The anatomy of a humanoid robot’s bill of materials, Exhibit 1

The analysis places actuators at 40–60% of humanoid hardware BOM and warns that hand components overlap with actuation and sensing categories.

Limit: An analyst reference range, not an audited OEM cost disclosure, universal target or statistical confidence interval. It does not determine this model’s prices.

Unitree Robotics

G1 official product specifications (opens in a new tab)

Publication: Undated on the linked document · Accessed October 27, 2026

Locator: G1 Parameter → Total Degrees of Freedom / Single Hand Degrees of Freedom

The base G1 lists 23 joint DoF; EDU configurations list 23–43. Optional hands change the configuration.

Limit: Configuration evidence only. No itemized actuator BOM or actuator cost percentage is disclosed on this page.

Goldman Sachs

Global Automation: Humanoid Robot — The AI accelerant (opens in a new tab)

Publication: 2024-01-08 · Accessed October 27, 2026

Locator: Public redacted PDF, cover and printed page 2

Historical analyst estimate: high-spec robot BOM fell from about $250,000 to $150,000 in 2023, a 40% decrease.

Limit: A historical analyst estimate, not an OEM cost disclosure or a validated 2026 actuator share. It does not calibrate this calculator.

Harmonic Drive LLC

CSF Mini Series: Principle and Structure (opens in a new tab)

Publication: Undated on the linked document · Accessed October 27, 2026

Locator: Printed pages 7–8, Definition of Ratings / Strength and Life

The catalog separates rated, repeated peak and momentary peak torque, and requires load-cycle-based selection.

Limit: Applies to the named gearhead series. It does not establish a universal actuator price, overload capacity or robot duty rating.

Boston Dynamics

An Electric New Era for Atlas (opens in a new tab)

Publication: 2024-04-17 · Accessed October 27, 2026

Locator: Official announcement of the fully electric Atlas platform

Boston Dynamics announced a fully electric Atlas, succeeding the hydraulic platform.

Limit: Architecture context only. The announcement does not quantify actuator BOM or a maintenance-cost reduction.

Continue from budget to joint selection

Request a scoped actuator quote